Does a 1984 datson have disk brakes on the front?

1 ANSWERS

1. amomipais82
   

   HI There,
   Types
   
       * Drum front/drum rear - Standard trim, Deluxe trim
       * Disc front/drum rear - GL, GX and optional on Deluxe
   
   The 1200 front-disc/rear-drum system was good for 1971. In fact, stopping power was better than most 'muscle cars' of the era. However, if you have a drum/drum system, you'll want to upgrade to disc/drum. The drum system stops well enough, but the disc system has less fading going down mountain roads.
   
   
   [edit]
   Calipers
   
   Calipers are used with disc brakes. Datsun B110, B210 and B310 used floating two-piston ANNET types.
   
   Type
   
       * B110: ANNET 12/14A (1.894" cylinder inner diameter)
       * B310 small: AN-18 (1.894" cylinder inner diameter)
       * B310 large: Disc-AN20 (2.012" cylinder inner diameter)
   
   
   Caliper bolt spacing:
   
       * ~84 mm: B110
             o and all 12" wheel B210 and B310
       * 88.9 mm: B310 large struts for 13" wheels
   
   [edit]
   Rotor Sizes
   Dia. (mm) Part Number Source
   212.5 40206-H1006 B110, B210 with A12 1974, 1975
   220 (AN18) 40206-H7500 B210 A12 1976-1978,B310 with 12" wheels
   232 40206-A1155 B210 A13, PB110?, PB210 early?
   245 (AN20) 40206-U6700 A10, B210 A14, B310 A14/A15, PB210 late?
   ? ? B210 Australia-assembled
   ? (Girlock) ? A10, Australia-assembled
   
   Apparently the calipers are unique for each rotor, also the strut/spindle assembly *may* be different.
   
   
   [edit]
   Rear Drum Brakes
   
   The same rear brake drum was used 1967-1994. It is an 8" diameter cast iron drum, that fits 1-3/8 wide brake shoes. Sunny Trucks started using a different brake shoe from Oct 1989.
   [edit]
   Specs
   
       * Linings (shoes)
             o 35 x 4.8 x 195 mm (width x height x thickness)
             o 1.378 x 0.189 x 7.68 inch (W x H x T)
             o 1-3/8 x ~3/16 x ~7-11/16 inch (W x H x T)
       * Total breaking area: 273 cm² (42.3 sq. in.)
       * B110: (manual adjusting)
             o Cylinder: 11/16" with front discs
             o Cylinder: 13/16" with front drums
       * B310: Drum LT-20 (auto adjusting)
             o Cylinder: 13/16" (20.64 mm)
   
   1978-1989 B120 ute used rear type Drum-LT20 with front type Drum2L20.
   [edit]
   Finned Alloy Brake Drums
   
   1692.jpg
   
       * The fins look like structural type, not cooling type.
   
       quote Datsun Competition Dept supplied it's favoured teams with many experimental parts that were never sold over the counter. 1200s had alloy drums and calipers fitted as wellas the alloy diff heads from the wagons.
   
   16780.jpg
   
   
   6262.jpg
   
       * Finned drums like these were offered by Datsun Competition in Japan.
   
   [edit]
   Specifications
   brake cylinders B110 (disc) 1977 US B210 1980 US B310 (Disc-AN20) 1980 Canada A12A (Disc-AN18)
   Proportioning valve not used yes 1,961 kPa x 0.4 psi 1,961 kPa x 0.4 psi
   Booster (Master-Vac) not used ? M60 6-in diameter 135mm rod length (flange-to-pedal) M60 6-in diameter
   Master diameter 11/16 inch 3/4 inch 13/16 13/16
   Front cylinder diameter 1.894 inch (drum brakes: 11/16) 2.012 inch 2.012 inch 1.894 inch
   Rotor diameter 212.5 mm 245mm 245mm 220mm
   Pad (width x length) 42.5 x 53.1 mm 41.2 x 63.4 mm 41.2 x 61.4 mm 42.0 x 56.8 mm
   Pad thickness 10.3 10.0 10.0 10.3
   Total front braking area (discs) 14.0 sq in 16.2 sq in ~14.6 ~13.8
   Total front braking area (drums) 42.3 sq in n/a n/a n/a
   Rear cylinder diameter disc brake models: 11/16 inch (all-drum models: 13/16) 13/16 inch 13/16 13/16
   Drum diameter 8.0 inch 8.0 inch 8.0 8.0
   Drum width 1.378 inch 1.378 inch 1.378 1.378
   Total rear braking area 42.3 sq in 42.3 sq in 42.3 42.3
   [edit]
   Part Numbers
   
   http://www.rockauto.com
   [edit]
   Front Brake Hoses
   
       * Length=11" End A Size=M10X1 End B Size=M10X1
       * RAYBESTOS BH36892; DORMAN H96862; ACDELCO 18J2188, 18J126, 19173109
   
   [edit]
   Rear Brake Hose
   
       * Length=13.188" End A Size=M10X1 End B Size=M10X1
       * RAYBESTOS BH36866; DORMAN H36866
   
   [edit]
   Pads
   
   8912.jpg
   
   
   Small Pad (58 mm for 212mm rotor) Fits:
   
       * 1971-1973 B110
       * 1973-1974 Civic USA
       * 1976-1978 F10 USA
       * 1979-1982 N10 (Datsun 310) USA
       * 1978-May 1979 PA10 Stanza GL, GLX
   
   Raybestos PGD104, Wearever D41, Bendix D104, Beck/Arnley 0880100D?, ACDELCO 17D104 (18028686), ACDELCO ACD39, ACDELCO ACD122
   
   Medium Pad (for 220mm rotor) fits:
   
       * B310 A12A Canada (220mm AN18 rotor)
   
   Beck/Arnley 0820100 Premium Organic $9.18
   
   
   Large Pad (63.5 mm for 245 mm rotor) RockAuto for AN20 rotor PartsAmerica fits:
   
       * 1974-1978 Datsun B-210
       * 1975-1979 Civic USA
       * 1977-1979 Datsun 200SX (S10)
       * 1979-1982 Datsun 210 (B310) USA
       * 1975-1976 Datsun 610
       * 1975-1977 Datsun 710
   
   Raybestos SGD117, PGD117 or RPD117, Beck/Arnley 0870944, 0820944 or 0880944D, Wearever D103, Bendix D103, ACDELCO 17D117 (18028692)
   
   D103 also D113. KD-29, MK D1008, AK A-33K
   
   
   [edit]
   Rear Brake Shoe
   
   set (8 x 1-3/8, fits B110, B210 and B310)
   
       * RAYBESTOS 371PG $15.36
       * WAGNER PAB371 $16.52
       * ACDELCO 17371B $19.02
       * WAGNER BD60368 $39.89
   
   
   [edit]
   Rotor
   
       * Front disc inner wheel bearing {Taper Bearing Assembly / Cone Length=0.5906 Bore=0.9843 Outer Diameter=2.0472 Width=0.6398 Cup Length=0.5118 Cone Radius=0.06 Cup Radius=0.06}
             o BECK/ARNLEY 0513809 $13.61
             o BCA 30205 $14.73
   
   
   http://www.rockauto.com
   [edit]
   Wheel Bearings
   
   Rockauto.com
   [edit]
   FRONT INNER
   
   Same bearing is used on drum brakes and disk brake hubs.
   
   Nissan 52 mm O.D.
   
       * 40210-H1000 ASSY-BEARING FRONT WHEEL INNER from 0570
       * 40210-18000 ASSY-BEARING FRONT WHEEL INNER to 0470
             o BCA/NATIONAL 30205
             o TIMKEN 30205M
             o BECK/ARNLEY 0513809
   
   Specs: Taper Bearing Assembly
   
       * Cone Length=0.5906"
       * Bore=0.9843"
       * Outer Diameter=2.0472"
       * Width=0.6398"
       * Cup Length=0.5118"
       * Cone Radius=0.06" Cup Radius=0.06"
   
   
   [edit]
   FRONT OUTER
   
   Same bearing is used on drum brakes and disk brake hubs.
   
   Nissan 42mm O.D.
   
       * 40215-H1000 ASSY-BEARING FRONT WHEEL OUTER from 0570
       * 40215-18000 ASSY-BEARING FRONT WHEEL OUTER to 0470
   
             19999.jpg
   
             o BCA/NATIONAL 30302
             o TIMKEN 30302
   
   Specs: Taper Bearing Assembly
   
       * Cone Length=0.5118"
       * Bore=0.5906"
       * Outer Diameter=1.6535"
       * Width=0.561"
       * Cup Length=0.4331"
       * Cone Radius=0.06"
       * Cup Radius=0.06"
   
   
   [edit]
   Rear Wheel Bearings
   
   See Axle Shaft. These are not easily replaced.
   [edit]
   Caliper
   
       * Bore Size=1.89" Inlet Thread=M10X1 Bleeder Thread=M10X1
       * Right: RAYBESTOS FRC3021 $30.79, RC3021, A-1 CARDONE 19124, 17124
       * Left: RAYBESTOS FRC3022 $30.79, RC3022, A-1 CARDONE 19125, 17125
   
   
   [edit]
   Parking Brake Cable
   
       * 48-1/4" Overall Length, 2 Per Car
       * RAYBESTOS BC92888 $39.79
       * ACDELCO 18P154, 18033072 $48.79
   
   
   [edit]
   Master Cylinder
   
       * Bore Size=11/16" Number of Ports=2 Primary Outlet Size=M10x1 Secondary Outlet Size=M10x1
       * A-1 CARDONE 111655 Remanufactured $26.79
       * RAYBESTOS MC39087
       * ACDELCO 18M1072, 19106858
   
   [edit]
   B120
   
   Front Disk Brakes from 8910. These are unique as they fit the same strut as the former drum brake setup.
   [edit]
   Rear Drum Brake
   
       * 44060-G0300 SHOE ASSY-REAR BRAKE SHOE 7510-7611
       * 44060-G0325 7612-8910
       * 44060-G1225 8910-
       * 43206-18000 DRUM BRAKE-REAR
   
   [edit]
   Master Cylinder
   
   Master cylinder has two bolts in horizontal plane; previous drum brake system used two bolts in vertical plane (like B110).
   
   
   [edit]
   Front Discs
   
   20072.jpg
   
       * 41060-G1985 PAD KIT-DISC BRAKE
   
       * 41001-G1500 CALIPER a*s'Y-FRONT RH W/O PADS OR SHIMS [Floating caliper]
   
       * 41121-05A10 PISTON-CYLINDER $31.23 [~1.8 inch (~45.2 mm)]
             o Pulsar SE 1988-1989
             o NX SR20DE, w/o abs 1991-1993
             o Sentra, gasoline, wagon 1988-1989
             o Sentra, SR20DE 1991-1994
   
       * 47210-G1500 BOOSTER ASSY-BRAKE
       * 40207-G1501 ROTOR-DISC BRAKE, FRONT [232 mm?]
   
   20073.jpg
   
   19075.jpg
   
   20075.jpg
   
   20076.jpg
   [edit]
   Disc pads
   
   For Sunny Truck
   
       * Nissan 41060-G1985 PAD KIT-DISC BRAKE
             o 108.3 or 108.5 mm width?
             o 8-97029-980 41060-G1985 04491-17011 41060-M3228 AY040-NS828 D400-7289 MB699174 V9118-B005
             o Rotex RT-1080, Akebono A-311K, MK Kashiyama D1080
             o 41060-G1585
             o Sumitomo SN831
       * Nisshinbo PF-2306 (108.0 mm width)
       * Tokico Stopal XN289
       * Stopping Revolution (SR) SR289 B122 8910-
             o 4996327027218, SRPF159N
       * Endless ES149NA
       * D-Speed DP071
       * Akebono 1216594955 Kashiyama
   
             akebono.jpg
   
       * Akebono 1216595007
   
             kashiyama.jpg
   
       * Akebono AN-31 1K (AN-311K) A311K
   
             20074.jpg
   
   [edit]
   Mystery
   
       * Rotor about 8"(203 mm).
   
             16913.jpg
   
             o total width of backing plate: 4-5/16 inch (109.5 mm)
             o Same as Subaru Justy for 12" wheel? Type 480
             o not 289, 291, 311, 314
   
   Are these the same?
   
       * 17125.jpg
       * 108.5 mm total width x 40.3 mm x 14.7 mm thick
             o ~4.272" x 1.587" x 0.579" (inch)
             o 4-17/64
       * Interpart GBP666
             o CHERRY 1.0 1.3 1.3VAN 1.5 DE 09/82 A 08/86
             o CHERRY 1.5TURBO DE 09/82 A 05/84
             o CHERRY 1.6 DE 09/85 A 08/86
             o SUNNY 1.0 DE 06/86 A 10/88
             o SUNNY 1.3 DE 05/82 A 05/89 + 1.3 KOMBI DE 05/82 A 08/90
             o SUNNY 1.4 DE 10/88 A 12/90
             o SUNNY 1.5 DE 05/82 A 09/88 + 1.5 KOMBI DE 09/83 A 05/86
             o SUNNY 1.6 1.6COUPE DE 08/86 A 05/89
             o SUNNY 1.6I 1.6I COUPE DE 10/88 A 09/90
       * Lockheed/Delphi LP261
       * Bendix 552206/552208
       * Bosch 986469580
       * Ferodo FDB293
       * Lucas/TRW GDB288/GDB988
       * Quinton Hazell BP229
       * Nissan 41060-01A25,41060-01A85,41060-12A25,41060-13A25,41060-13A90,41060-25A25,41060-61A86,41060-62A90,41060-62A92,41060-67A90,41060-89A90,41060-89A91,DA060-13A85
       * Nissan 41060-77A91AS Pulsar, carb, 1984-1985 to -0485
             o Part number 41060-01A25 was superceded by part number 41060-77A91AS
       * Subaru 725191220 725191631 725191990 725193121
   
   
       * USA Nissan Pulsar 1984 2BBL carbureted
       * Nissan 41060-01A25
             o Nissan 41060 77 A91AS
       * WAGNER PD233/ZD233 or MX275, GUARDIAN 61233, MONROE DX275/CX275, AKEBONO ACT275, Brake Best MKD275, Raybestos RPD266M/RPD266/PGD233/RPD233, Centric 10002750, Beck/Arnley 0891243/0871243/0821243/0881243D/0881243M
             o 1983 Nissan Pulsar L4 1.6 Liter Carbureted - VIN P
             o 1983-1986 Nissan Pulsar NX 1.6 Liter Carbureted
             o 1987 Nissan Pulsar NX XE L4 1.6 Liter FI - VIN P (CA16DE)
             o 1988-1990 Nissan Pulsar NX
             o 1982-1990 Nissan Sentra
             o 1984-1985 Nissan Stanza
   
   
   Hope it helps

   Report (0) (0)  |   12 years, 8 month(s) ago